A few months ago we tackled our biggest project yet – a DIY Kitchen Remodel for my parents. We completely re-did the entire kitchen from the ground up. New floors, new walls color, new cabinets, new everything (except the stove). It was quite a project.
Last week I posted the first of the series about the kitchen remodel – the demolition. Whew – that part of the project was a lot of work!
The next step is the walls. But first a quick recap.
And at the end of the first blog post the kitchen looked like this:
The demolition portion of the DIY Kitchen Remodel took the better part of three days. In that time we cleared out all the furniture, appliances and old cabinetry and removed the wallpaper from the walls.
Those walls had held wallpaper for over 30 years, the latest edition being at least 20 years old. Once the wallpaper was removed the walls behind it weren’t exactly in great shape. In fact, in some places the walls were in rough enough shape I was very glad we planned to put up a tile backsplash so I didn’t have to waste a lot of time patching them up.
Thankfully, the walls in the dining section of the room were in decent shape but had never been textured. We borrowed a texturing machine from a friend for that step.
In preparation for the walls we filled any holes, caulked along any cracks in the corners (there were quite a few of those along the ceiling), and added a couple of outlets (for the dishwasher and microwave).
*When caulking anything you intend to paint double check that the caulk DOES NOT have any silicone in the ingredients even if it is labelled as paintable. Learned that one that hard way and had to do a lot of touching up later as the tape pulled off the paint over the caulk. Urgh.
Texturing a wall isn’t hard. In fact for small patches you can buy a spray can like THIS. (I have used that in other rooms – works great!)
For larger jobs, first fill any nail holes and patch any dents and sand smooth. Then take the time to cover anything that you don’t want textured (that stuff gets everywhere!). We taped plastic over all of the light fixtures, trim, heaters, and openings for doors and windows. We didn’t worry about the floor because we knew we were going to remove the first layer of subfloor and replace it before tiling the floor. That’s why we chose to do the texturing at this point – fewer things to cover up and protect from overspray than at any other point in the install.
As I said, we borrowed a texture spray gun from a friend. It looked similar to THIS ONE, which really isn’t a bad price. (I may just have to look into getting one when we build the new house. Something to think about…) Or if you don’t have an air compressor you could use a texture spray gun like THIS.
Once you’re all set up, simply mix the texture to the right consistency (roughly pancake batter in our case – it will depend on the texture you desire) and experiment a little bit on a scrap piece of cardboard or something.
There are a number of different texturing techniques. We went for the simple “orange peel” look.
-move quickly as you don’t want it to build up on the walls. You can always go back and apply another thin coat if needed but it’s not so easy to remove something that was put on too thickly.
-apply using a more circular motion (as much as possible – the sprayer is kind of awkward) instead of straight lines.
-try not to be a perfectionist. Remember – no one looks at the finished project as closely as you do when you are putting it together.
Let dry completely before removing the tape and protective plastic. In our case we applied the texture as the last thing we did on Day 3, at 8:30 PM. *sigh*
There you can see the walls with the texture applied. Sorry I forgot to get a close-up at that stage. Most of the photos were snapped quickly with the cell phone while everything was in process.
As you may notice from the photo, after texturing the walls we started painting. If you’re smart about this step you can save some time by not having to tape everything for each step.
We started by painting the ceiling and trim white. I suggest satin or flat paint for the ceiling, semi-gloss or high gloss for the trim. The glossier the trim is, the easier it is to clean later.
Then I taped off the ceiling and trim and started on the wall color.
I love how productive painting the walls feels. Suddenly the mess of a kitchen starts to look like it’s coming together. Amazing how a little bit of color can do that.
Well, that a good place to stop for today. Next up – installing the tile! (and yes we did it all ourselves – it’s easier than you think!) Check back soon!
*Post may contain affiliate links.